SHIM-ME

Specs

Tested. Documented. Made in the USA.

Sizes, heights, parts and options, with the test files and documents behind them.

Specifications

Design
Adjustable, interlocking aluminum shim system
Sizes (Unit Width)
2", 3", 4", 5", 6". Custom sizes available.
Height
About 1¼" lowest, about 1¾" maximum before the extension
Adjustment
About 1/16" per notch
Extension
Adds 1⁄2" height each. Stack to build up to about 8".
Base-Plate Spacing
Maximum 8" edge to edge (Installation Manual)
Material
Aluminum
Thermal Break
Optional, on every size
Tape
3M VHB Tape 5962, optional
Parts
Base plate, wedge set, ½" extension, thermal break, screws
Made In
Boise, Idaho, USA

Test Files

SHIM-ME profile under compression in a load frame
Test bench photo

Strength

Compression Load and Deflection

Aluminum SHIM-ME specimens loaded in a compression frame in three configurations: lowest position, raised on 2 teeth and raised on 4 teeth. Load and displacement were recorded for each specimen.

Thermal test setup: SHIM-ME assembly under a frame section with thermocouple probes
Test bench photo

Thermal

Thermocouple Probe Test

Type K thermocouples on the frame side and the base side of the assembly, with dry ice at about −109°F as the cold source. The frame side stayed significantly warmer than the base side.

First page of the 3M VHB Tape 5962 datasheet
Manufacturer datasheet

3M VHB

3M VHB Tape 5962

The optional tape locks the base while you set the unit. Bond values are in the manufacturer's datasheet.

3M Datasheet (PDF)

Then vs. Now

The Full Comparison.

Close-up of stacked plastic shims between the sill pan and the track, with silicone sealant squeezed out around them
Then: Stacked Shims
Close-up of a SHIM-ME assembly on the sill pan: base wedge and adjustable wedge interlocked under the track
Now: SHIM-ME
TopicThen: Stacked ShimsNow: SHIM-ME
Setting the HeightThen:Loose pieces stacked and trimmed at every openingNow:Set notch by notch, about 1/16" at a time
Under LoadThen:Crush and settle over timeNow:Parts interlock into one solid aluminum unit
DrainageThen:Clog the drainage path, causing leaks and stucco crackingNow:Clear drainage path
Who Installs ItThen:Needs your most experienced installerNow:Any crew member levels it on the first try with a tape measure and a level

Fewer leak callbacks. Fewer warranty claims. Doors stay square.

The Labor Math

Up to 15 minutes saved per linear foot, or $12.50 at $50/hr.

Estimates, from the calculator: up to 2 hours saved for every 8 linear feet of install, at $50 per hour.

Use the Calculator
Labor saved by total linear feet
Linear feetHours savedLabor saved
8 ft2 hrs$100
50 ft12.5 hrs$625
100 ft25 hrs$1,250
300 ft75 hrs$3,750

Thermal Performance

Thermal Performance.

The optional thermal break adds an insulating barrier between the slab and the frame. In the thermocouple test, the frame side stayed significantly warmer than the base side.

See the Thermal Test →
2-inch SHIM-ME unit with the black thermal break on top
2" unit with thermal break

FAQ

Before You Switch.

What Sizes Are There?

2", 3", 4", 5" and 6" unit widths in stock, plus custom X sizes on request.

Ask About a Custom Size →
Do I Need the Thermal Break?

It's optional and available on every size. It sits on top of the assembly, under the window or door rail.

What Does the 3M VHB Tape Do?

The optional 3M VHB Tape 5962 locks the base while you set the unit. Bond values are in 3M's datasheet.

Open the Datasheet →
What Load Does It Take?

15,000 lbs rated load. The compression test data is on this page.

See the Strength Data →
How Does It Ship?

UPS Ground from Boise, Idaho.

Can I Return It?

Within 30 days, on unused units with the tape intact.

Does It Replace Sill Pans?

No. SHIM-ME anchors to the sill pan; it doesn't replace sill pans or other required components.

Downloads